Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Newport News?
Gate installation in Newport News typically costs between $2,800 and $11,500 for a single residential driveway gate, installed with an operator, and between $1,200 and $3,600 for a pedestrian walk gate. A basic manual swing gate sits at the low end; a wide slide gate with an electric operator, safety loops, and a keypad lands at the high end. The written estimate sets the final price, and every estimate we provide is free.
We install gates in Newport News with a single focus: gates, nothing else. Our technicians have up to 14 years of experience with swing arm, slide, and barrier arm systems across nine operator brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Whether you’re replacing a tired manual gate or adding an automatic driveway entrance, the process starts with a site visit and a clear number.
Key Takeaways
- A single swing gate with an operator typically runs $2,800-$7,500 in Newport News.
- A slide gate with electric operation usually runs $5,500-$11,500 depending on width, footing, and safety hardware.
- Manual gates cost less to install but less convenient to use on a wide driveway.
- Permits, grading, and electrical work are the three items that move the estimate most.
- We service what we install, so repair support doesn’t require a second contractor.
Gate Installation Cost Breakdown (2026)
Below are typical installed price ranges for the Newport News market. Every line item is estimated; the written estimate you receive after a site visit is the number that counts. Call (866) 620-2654 for a free estimate on your property.
| Project Type | Typical Installed Range (2026) |
|---|---|
| Pedestrian walk gate (manual, up to 4 ft) | $1,200-$2,400 |
| Pedestrian walk gate (manual, 4-6 ft, higher grade) | $1,800-$3,600 |
| Single swing driveway gate (manual) | $2,800-$5,400 |
| Single swing driveway gate with electric operator | $4,200-$8,200 |
| Single slide gate (manual, up to 12 ft) | $4,500-$7,200 |
| Single slide gate with electric operator | $5,500-$11,500 |
| Dual swing gates (double driveway) | $6,800-$13,500 |
| Barrier arm gate (light commercial driveway) | $4,800-$9,500 |
| Gate operator replacement (existing gate, new operator) | $1,600-$4,200 |
| Safety loop detectors (per loop, installed) | $350-$750 |
| Keypad or telephone entry system (residential grade) | $450-$1,200 |
| Keypad or entry system (commercial grade, DoorKing-class) | $1,200-$3,400 |
| Gate removal and disposal (existing gate) | $250-$600 |
| Grading and site prep (light) | $400-$1,600 |
What drives the estimate up? Width and weight first, because a heavier gate needs a stronger frame, deeper footings, and a heavier-duty operator. Second is the operator itself: a simple residential swing arm runs less than a commercial slide operator with an integrated control board and loop detectors. Third is the site: a flat, straight driveway with easy power access is a straightforward job, while a sloping drive, a curve, or a run to a distant panel adds labor and trenching. Fourth is access control: keypads, telephone entry, and intercom systems climb in price as they get more capable. And fifth is whether any permits apply to your property, since the city of Newport News may require a permit for a gate and its electrical work; your city’s building department will tell you exactly what’s needed.
What Affects Gate Installation Pricing in Newport News
- Gate width, height, and material. A 12-foot slide gate in steel costs more to install than a 4-foot aluminum walk gate. Wider gates need bigger footings and heavier operators. Heavier gates need thicker frames and a stronger post. The weight of the gate dictates most of the hardware below it.
- Operator brand and type. LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule all have different price points and installation requirements. A residential-grade operator with a built-in receiver runs less than a commercial-grade unit with loop detection and heavy-duty motor. Matching an operator to the gate weight and the driveway length matters as much as the brand.
- Power and low-voltage wiring. If power isn’t at the gate location, running a conduit and circuit adds cost. Loop detectors, safety edges, and photo eyes each add hardware and labor. A gate with no convenient power access is a different job than one next to an existing outlet.
- Grading and driveway conditions. A level driveway makes a straight run to the gate straightforward. A slope or a curve changes where the gate sits, how the footing is poured, and how the operator is set up. Soil conditions and drainage also affect how deep the footing posts go.
- Permits and code requirements. The city of Newport News and the relevant county building department set the rules for gate permits and electrical work. Most installations that involve an electric operator and new low-voltage wiring will need to be checked against local requirements, so ask before the project starts. Permit fees are separate from installation labor and are typically in the $150-$500 range for a residential gate project, depending on what’s included.
- Access control and safety hardware. Keypads, telephone entry, safety loops, photo-eye beams, and safety edges are optional on a manual gate but standard practice on an automatic one. Each piece adds a line to the estimate, but skipping any of them is a risk to people and property.
How to Save on Gate Installation
Installation pricing isn’t rigid. There are real ways to lower the number without cutting the parts that matter.
- Choose a standard gate size. A single gate at a common width uses stock components and takes less time than a custom build. Width and weight are the two biggest levers on cost.
- Bundle the operator and the gate. Installing a new gate and a new operator together usually costs less than installing a gate now and adding an operator later. The footings and wiring can be planned for both from the start.
- Keep the gate close to existing power. A gate location near an existing outlet or panel cuts the trenching and conduit work. That’s often one of the larger labor line items.
- Install the safety hardware at the same time. Loop detectors and safety edges cost less as part of the original install than as a retrofit. They also work better when they’re planned into the gate from the beginning.
- Ask about the install and the service as a package. We install it and we service it, so there’s no scrambling to find a second contractor when the operator needs a control board or the limit switches drift.
- Get a free written estimate. The estimate is free; call (866) 620-2654 to schedule a site visit. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday.
One word on safety: an automatic gate is a heavy moving object, and the operator’s wiring and power supply are genuinely dangerous to work on without training. We don’t give step-by-step DIY instructions for installing or wiring an automatic gate. A gate that closes on a person or a vehicle is a hazard, and a gate with a miswired operator can fail open or fail closed. This is a job for a trained technician who has worked with the specific operator brand on your property.
Manual vs. Electric Gate Installation in Newport News
Manual swings and slides are the lower-cost route, typically $1,200-$5,400 installed depending on size. Electric gates run $4,200-$13,500 installed, depending on width, operator grade, and safety hardware. The gap isn’t just equipment cost. It’s the operator, the low-voltage wiring, the safety loops, and the electrical work that make an automatic gate safe and reliable. If your driveway opens onto a busy road, or if you want to control access without leaving the car, the electric route is usually worth it. If the gate is at the back of a quiet lot and a person opens it by hand, a manual gate is the sensible choice.
For a fuller look at what we do and where we work, see gate repair Newport News. It’s the same specialist focus, applied to the repair side of the work.
What Brands and Gate Types Do We Install?
We install and service swing arm, slide gate, and barrier arm gates. On the operator side, we’re trained and experienced on nine brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers common residential openers and harder-to-find commercial-grade systems. It also means we can service and repair the operator on an existing gate, which is a big part of why customers call us before a generalist fence contractor.
Gate types we install:
- Swing gates. Single or dual, residential and light commercial, manual or automatic.
- Slide gates. Single-track and cantilever, with or without electric operation, safety loops optional but recommended.
- Barrier arm gates. Light commercial driveway and parking access.
- Pedestrian and walk gates. Manual and electric, including matching entry gates for a property with a driveway gate.
If your property is in Newport News and you already own an operator on your list but the gate itself needs replacement, that’s a full-cycle job for us, not two contractors. If you’re in a nearby city, check our Newport News page for coverage details and the surrounding area.
Same-Day Installation? How Scheduling Usually Works
New installation is a scheduled project, not a same-day call. We start with a free on-site estimate, measure the gate, confirm the operator and safety hardware, and give you a written number. From there, the install is scheduled around material lead times and, if a permit applies, the city’s review. For repairs on an existing gate, including electric gate repair on a control board, loop detector, limit switch, or operator motor, we do offer same-day service when the schedule allows. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday.
FAQs – Gate Installation Cost
How much does a gate cost to install in Newport News?
A typical single residential gate in Newport News costs $2,800-$7,500 installed, and a pedestrian walk gate costs $1,200-$3,600 installed. Slide gates with electric operators run higher, typically $5,500-$11,500. The written estimate sets the final price. Call (866) 620-2654 for a free estimate – estimates are free.
Is it cheaper to install a manual gate or an electric gate?
A manual gate is cheaper up front, typically $1,200-$5,400 installed versus $4,200-$13,500 for an electric system. The electric route costs more because of the operator, low-voltage wiring, safety loops, and electrical work. Choose manual if the gate is opened by hand and access control isn’t a priority. Choose electric if the driveway opens onto traffic or you want entry without leaving the car. Call (866) 620-2654 if you’re unsure which fits your property.
How long does gate installation take in Newport News?
A simple manual walk gate can be installed in a few hours, and a single automatic driveway gate typically takes a full day or a day and a half, depending on gate weight, site conditions, and whether the operator and safety hardware are part of the install. Projects that need a permit or significant grading take longer. Call (866) 620-2654 to talk through your timeline.
Do I need a permit to install a gate in Newport News?
Many gate installations in Newport News, especially those with an electric operator and new wiring, require a permit from the city. The permit requirement and any associated fees are set by the city’s building department, so ask before the project starts. Permit fees are typically a few hundred dollars and are separate from our installation labor. Call (866) 620-2654 for a free estimate.
Can you install a gate on an existing operator that’s already on my property?
Yes. We install gates on existing operators and service the same brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If the existing operator is the right size and condition for the new gate, it can often stay. Call (866) 620-2654 for a free estimate and a look at your current setup.
What drives the cost up the most on a gate install?
Width and weight of the gate, operator grade, and the electrical run are the three biggest cost drivers. A wide slide gate with a commercial operator and a long conduit run will always cost more than a standard swing gate next to an existing outlet. The written estimate lines up each item so you can see what’s driving the number. Call (866) 620-2654 for a free estimate.
Get a Free Gate Installation Estimate in Newport News
Installing a gate is a project that benefits from a technician who knows the operator brands, the gate types, and the local permit landscape. We do gates exclusively, from repair through new install, and our technicians have up to 14 years of experience working with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. The estimate is free, the pricing is upfront, and the written estimate is the number that counts.
Call (866) 620-2654 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Written by the team at Gate Repair Newport News.
Pricing reflects the Newport News market as of 2026. Gate Repair Newport News offers free estimates – call (866) 620-2654.
What Our Customers Say
"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Tiana Whitfield"Repair is holding. He was quite a bit later than the window I was given, and nobody called me about it, I had to call them. The work itself was done well once he got here."
- Latoya Freeman"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Emily Yang