Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Electric Gate Repair for Newport News Homeowners
A gate that won’t open strands you in your own driveway. It’s worse when it’s stuck open and the property sits unsecured until someone can look at it. We handle electric gate repair in Newport News as a single trade: swing arm, slide gate, or barrier arm, from motor to control board. Our technicians have up to 14 years of experience, so we recognize the operator on your property quickly instead of guessing. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule equipment. When a gate fails, call (866) 620-2654. We answer 24/7, and fast dispatch from 7am to 7pm gets a technician to most Newport News addresses the same day.
Gate Opener Repair
Gate Opener Repair covers the unit that drives the gate: the motor, the gearbox, the limit switches, and the control board that tells everything when to move and when to stop. You need it when the gate runs but won’t latch, reverses halfway, opens partway and quits, or the remote works only when you’re standing close. We test the operator under load, check the limit settings, and confirm the board is sending the right signals to the motor. Most opener repairs in Newport News land between $180 and $650 depending on the failure, and we quote a written estimate before anything starts. Call (866) 620-2654 for an exact quote.
Limits and Reversal Settings
If a gate stops short or reverses at the same spot every time, the travel limits or the safety reversal setting is usually the culprit. We reset them to the gate’s actual travel and confirm the gate reverses properly when it meets an obstruction. These adjustments take a single visit and prevent the operator from straining against its own limits.
Remote and Receiver Pairing
A remote that only works close up usually points to a tired receiver or a weak antenna connection, not a dead battery. We test the receiver, clear out old codes, and pair your remotes and keypads cleanly to the board. You leave with every remote working from the end of your driveway.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Automatic Gate Repair
Automatic Gate Repair addresses the whole system that lets a gate move on its own: operator, sensors, safety edges, wiring, and controls working together. It’s the service you need when the gate has power but behaves unpredictably, or when it opens on command but refuses to close. Our electric gate repair work at Gate Repair Newport News includes tracing faults through the control board, loop detectors, limit switches, and the operator motor itself. Typical automatic gate repairs in Newport News run $200 to $800 depending on which component has failed and how much wiring access the site allows. Estimates are free and the price is agreed before any work starts. Call (866) 620-2654.
Safety Edges and Loop Detectors
A gate that won’t close is usually telling you its safety circuit is holding it open. We test the safety edges and the loop detector, find the break or the failed sensor, and restore the circuit. We won’t just override a safety device to force the gate shut.
Control Board Faults
Erratic behavior, random reversals, or a gate that ignores commands often trace to a failing control board. We meter the board, check the inputs one at a time, and replace it when repair isn’t reliable. We match the board to the operator you already own.
Electric Gate Motor
Electric Gate Motor refers to the drive assembly that actually moves the gate, and it’s the part that takes the most wear over years of daily cycles. You need motor service when the gate moves slowly, grinds, hums without moving, or heats up and quits after a few cycles. Our technicians inspect the motor, the gearbox, and the drive mechanism, then tell you plainly whether a rebuild or a replacement makes more sense for your operator. Motor repairs and replacements in Newport News typically run $250 to $900 depending on motor type and gate weight. We quote in writing first. Call (866) 620-2654 for an exact quote.
Swing Arm and Slide Operators
Swing arm and slide operators wear differently, and we service both. Swing arms stress their hinges and pivots; slide gates wear the track and the rollers under the gate. Knowing which one you have speeds up the diagnosis and the parts order.
When a Motor Needs Replacing
A motor that still runs but struggles with the gate’s weight may be undersized for the load, or simply worn out. We measure the gate and check the duty cycle the operator was built for. If replacement is the honest answer, we say so and quote it.
Gate Access Control
Gate Access Control is the system that decides who can open the gate: keypads, card readers, intercoms, remotes, and phone-based entry. It needs attention when codes stop working, the keypad accepts a code but the gate stays put, or you can’t get the gate to open for a guest. We repair access control on residential and light-commercial gates, whether it’s a standalone keypad or an intercom tied into a DoorKing system. Access control repairs in Newport News generally run $150 to $600 depending on the device and the wiring involved. We give you a written estimate before we touch anything. Call (866) 620-2654 for a free estimate.
Keypads and Card Readers
A keypad that lights up but won’t trigger the gate usually has a wiring or programming fault rather than a dead unit. We test the connection to the board, re-enter the codes, and swap the keypad only if it’s actually failing. Card readers get the same treatment.
Intercom and Entry Systems
Intercom systems tie access control to your phone or a handset, and a fault anywhere in that chain can lock the gate shut. We trace the intercom circuit, test the release relay, and restore voice and unlock together. HOA managers in Newport News rely on this when a shared entry stops responding.
Commercial Gate Operator
Commercial Gate Operator service covers the heavier automated gates at small commercial properties, HOAs, and shared driveways where the gate cycles dozens of times a day. You need it when a gate that handles steady traffic starts failing, whether that’s a barrier arm at a lot entrance or a slide gate at a community drive. We work on commercial-grade systems from DoorKing and Elite alongside the residential operators most companies know. Commercial operator repairs in Newport News usually run $300 to $1,200 depending on the operator, the failure, and access to the equipment. Estimates are free and the price is set before work begins. Call (866) 620-2654.
High-Cycle Wear Points
Gates that open constantly wear out motors, gearboxes, and control boards much faster than a home driveway gate. We look at cycle counts where the operator tracks them and focus on the parts that see the most strain. That keeps downtime short.
Keeping Traffic Moving
A failed commercial gate stops everyone behind it, so diagnosis has to be efficient. We isolate whether the fault is power, operator, or access control before ordering parts. HOA managers who call us get a straight answer about what’s wrong and what it’ll take.
Brands We Service
We service LiftMaster equipment and know where those operators wear out, from the control board to the drive gears. FAAC systems are common on heavier swing gates, and we’re familiar with their hydraulic and electromechanical operators. BFT and Linear operators show up on a lot of residential installs, and we handle their control boards, limits, and remotes without needing a brand-specific dealer. For lighter residential gates, we service Mighty Mule and Ghost Controls, including the battery and solar setups some of them run on.
On the commercial side, DoorKing is everywhere at gated communities and lot entrances, and we work on their access control and operators together. Elite systems round out the heavy-duty work, and our technicians have up to 14 years of experience with those. We service Viking equipment too, including legacy units where parts can be harder to find. Whether you have a LiftMaster, a FAAC, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- The gate reverses or stops mid-travel. A gate that changes its mind is usually reading a faulty safety input or a bad limit setting. It can also mean a failing control board, and forcing it just wears the operator faster.
- The motor hums but the gate doesn’t move. That hum is the motor trying to drive against a jammed gearbox, a stuck gate, or a dead capacitor. Running it that way can burn the motor out.
- The gate won’t close at all. When a gate stays open, its safety circuit is holding it there, and you need it addressed rather than bypassed. A gate that won’t close also leaves the property exposed.
- Your remotes or keypad stopped working. If codes, remotes, and keypads all quit at once, the problem is in the receiver or the access control wiring. That’s a fast diagnosis for a technician.
- You hear grinding or see the gate dragging. Grinding points to worn gears or a gate off its track, and dragging puts strain on the motor every cycle. Left alone, a small mechanical fault turns into a motor replacement.
Our Process, Step by Step
- 1
We take your call and book the visit. You tell us what the gate is doing and what operator you have, if you know it. We answer 24/7, and a call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
- 2
We diagnose on site. A technician tests the operator under load, meters the control board, and checks the safety edges, loop detectors, and limits one at a time. We don’t guess and we don’t start swapping parts.
- 3
We quote before we work. You get a written estimate that names the parts and the labor, and the final price is agreed before anything is installed. No surprise invoice at the end.
- 4
We repair and test. Once the repair is done, we run the gate through a full open-close cycle and confirm the safety reversal works as it should. The gate leaves working the way it’s supposed to.
- 5
We tell you what to watch. If we spot something that will need attention later, like a worn gearbox or a tired keypad, we say so plainly. You decide when you want it handled.
How Much Does Electric Gate Repair Cost in Newport News?
Most electric gate repairs in Newport News fall between $150 and $900, and the range depends on which part failed. A simple remote or limit adjustment sits at the low end. A control board or motor replacement sits at the top. A typical opener repair runs $180-$650 depending on the operator and the failure. A motor or drive replacement runs $250-$900 depending on gate weight and motor type. Access control repairs land around $150-$600, and commercial operator work runs $300-$1,200. What affects the price most is the operator brand, how easy the wiring is to reach, and whether the gate needs a part ordered.
You avoid overpaying by getting a written estimate before work starts, and by asking whether the technician tested the board or just replaced it. Every estimate we give is free, names the parts and labor, and sets the final price before we begin. That way the invoice matches the quote and there’s nothing to argue about afterward. If the repair needs a part we don’t have on hand, we tell you the timeline up front so you’re not left guessing. Call (866) 620-2654 for a free estimate.
Our Service Area Near Newport News
We service electric gates across Newport News and the surrounding area, including Hampton, Norfolk, and Gloucester Courthouse. We also reach Claremont, Mathews, Gwynn, Waverly, Sedley, and Deltaville. Response times depend on where you are and the day, and most Newport News calls get a technician out the same day. If you’re outside the city, we’ll let you know the soonest opening when you call. For related work, see our electric gate repair page for the Hampton area.
Serving Newport News, VA – Our Local Coverage Area
We serve Newport News and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Electric Gate Repair in Newport News
Electric gate repair is fixing an automated gate so it opens and closes on command again, covering the operator, control board, safety devices, and access controls. It isn’t a hardware swap on a manual gate; it’s diagnosis of the electrical and mechanical systems that drive the gate. We handle swing, slide, and barrier gate types. For full details, see our electric gate repair page.
Most electric gate repairs take one to three hours on site once the technician has the right part. Simple fixes like a limit reset or a remote re-pair finish faster. If a control board or motor has to be ordered, the visit may be split into a diagnosis and a return. We tell you the timeline at the estimate. Call (866) 620-2654 for a free estimate.
Electric gate repair in Newport News typically costs $150 to $900 depending on the failure and the operator. Opener repairs run $180-$650, motor work $250-$900, access control $150-$600, and commercial operators $300-$1,200. The written estimate sets the final price before any work begins. Call (866) 620-2654 for an exact quote, estimates are free.
Yes, we service LiftMaster equipment along with FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We know where each of those operators wears out, so diagnosis is quicker than with a company that sees only a few brands. Whether you have LiftMaster or another make, we can help. Call (866) 620-2654 for a free estimate.
Yes, same-day service is available in Newport News depending on the day and the workload. We answer 24/7, and fast dispatch from 7am to 7pm runs Sunday through Friday. We’re closed Saturday. Call (866) 620-2654 and we’ll book the soonest opening.
We stand behind the repairs we make, and we’ll explain what’s covered when we hand you the written estimate. Warranty terms depend on the part and the repair, so we spell them out rather than making a blanket promise. Ask us on the call and we’ll give you a straight answer. Call (866) 620-2654.
Clear the area around the gate and the operator so the technician can reach the equipment, and make sure someone is available to open access to the property. If you have the operator’s manual or the original remote, have those handy. Don’t try to force a stuck gate open or closed. Call (866) 620-2654 to book.
Schedule Your Electric Gate Repair Service in Newport News Today
A gate that won’t move needs a technician who knows the operator on your property, not a generalist guessing at it. Call (866) 620-2654 and we’ll schedule a visit for your electric gate repair. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. The estimate is free, and we quote before any work starts. For new gates, see our electric gate repair services and installation work, and learn more on our gate repair page.
Written by the team at Gate Repair Newport News.